There are many types of screwdrivers, but the type of screwdriver you need to open JoyCon depends on the screws you are trying to remove. The most common type of screwdriver for this task is a Phillips head screwdriver.
There is no one-size-fits-all answer to this question, as the type of screwdriver needed to open a joycon will vary depending on the screws that are holding it together. However, some common screw types used in joycons are Phillips head screws, which require a Phillips head screwdriver to remove; and flat head screws, which require a flat head screwdriver to remove.
What screwdriver do I need to open Joycons?
A small Phillips (crosshead) screwdriver is all you need to remove the four black screws on the rear side of your Joy-Con. Once the screws are removed, slide the plastic shiv or chosen alternative down the seam between the two halves of the case to separate them.
When you need to open up your Joy-Con controller, be careful not to damage the inner components by sliding the opening pick too far inside. Instead, insert the pick into the seam at the bottom edge of the controller (opposite the L and ZL buttons) and slowly slide the flat edge up the side of the Joy-Con.
What kind of screw is in a Joy-Con
The iFixit Precision 4 mm Screwdriver Bit is a great tool for opening up electronic devices. It is very precise and makes it easy to remove screws without damaging the device.
The screws that you will need for this project are M1 4 x 5mm screws.
How big is a Y00 screwdriver?
This is a great little screwdriver tool for Y00 metal triwing screws. It’s well made and fits the screws perfectly. The only downside is that it’s a bit expensive.
Triangle screwdrivers are specifically designed for screws that have a triangle-shaped recess at the head. The sides of the triangle bit on the screwdriver are straight, which allows it to fit perfectly into the recess and engage with the screw. Tri-wing screwdrivers are common in the aerospace industry, as they are used with screws and bolts that hold together commercial aircraft.
How do you remove Joy-Con lock?
Unscrew the case screws and separate the halves of the Joy-Con. Open the Joy-Con and unscrew the charging rail. Remove the back panel and the buckle lock bracket. Slide one side of a pair of pointed tweezers under the flat part in the middle of the buckle lock bracket.
To detach the Joy-Con straps from the Joy-Con controllers, ensure that the slide lock at the bottom of the Joy-Con strap is in the unlock position. It is not necessary to press the release button on the back of the Joy-Con controller to detach the Joy-Con straps. Slide the Joy-Con strap from bottom to top.
How do you remove a stuck Joy-Con
To remove the Joy-Con from the Nintendo Switch console, start by holding the console in your left hand. For the right Joy-Con, hold it upright with the + Button positioned upward and the Joy-Con strap in the other hand. Firmly slide the Joy-Con upward. For the left Joy-Con, hold it upright with the – Button positioned upward and the Joy-Con strap in the other hand. Firmly slide the Joy-Con upward.
You will need a Y shaped screwdriver in order to open up and repair your Nintendo Switch Joy cons. This screwdriver can be found at most hardware stores.
What size screws does Nintendo use?
The 45mm gamebit was a cross-platform gaming device that was used by both Nintendo and Sega. It was first found in the Nintendo 64, and later in other gaming devices such as the Sega Genesis. The gamebit allowed for better gaming experiences by allowing players to cross-platform between different devices.
The standard size for switch plate screws is 6-32. This is the thread diameter of #6 and there are 32 threads per inch.
How do you remove switch Joy-Con screws
Every time like non-stop but don’t move around the other parts you’re gonna damage this part of the plant. So, it’s very important to know where your plant is from.
Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the four 37 mm screws securing the right Joy Con rail to the frame of the device.
Is Nintendo still replacing Joycons for free?
If you are experiencing problems with your Joy-Cons, you can send them to Nintendo for free repairs. Simply fill out a form on their website and you will be given a shipping label. You can send up to four Joy-Cons in a single box.
When using internal socket head type TORX screws, the following sizes are used:
Inch P to P:
T4 050 128mm
T5 055″ 142 mm
T6 066″ 170 mm
T7 078″ 199 mm
Metric P to P:
T4 050 128mm
T5 055 142 mm
T6 066 170 mm
T7 078 199 mm
Final Words
You need a Phillips #0 screwdriver to open the Joy-Con.
A Torx screwdriver is the type of screwdriver needed to open a Joycon.
